global
Send us a message
product

ITEMLIST

Products Infomation

NetVision MIPI Generator SVO-03-MIPI

MIPI Generator SVO-03-MIPI


Request a Quote
 
The MIPI Generator SVO-03-MIPI is a camera emulation board that video signals input from USB3.0 or HDMI to MIPI video signals and outputs them.

The images recorded on SVO-03-MIPI can be output to image processors, as if they were images from a camera module or CMOS image sensor.
CG images can also be used.

This makes it possible to develop image processors, even when recording on site is difficult or when you have not had sensors yet such as under developing them.

MIPI Generator

Model:

SVO-03-MIPI

Maker:

NetVision

Features

MIPI CSI-2 supports up to 1Gbps / lane

  • Input from USB3.0(Vendor Class) or HDMI
  • Compatible with 4Gbps automotive serializer

Application

Display video signal of camera modules or CMOS sensors to DisplayPort monitor,
Around view development, Simultaneous monitoring of multiple sensors.
■ Application Areas
Automotive / transportation equipment, medical testing / analysis / measurement, IT / information / communications, software, education / research institutions, and so on.

 

 

 

 

SerDes Interface Boards Specification List

Video 

Specifications

■ Specification

Table Item Specification Remarks
Video input interface USB3.0 (Windows)
HDMI (Up to 1080P-60fps)
Special HDMI monitors are available individually
Video output interface MIPI CSI-2 video signal Supports FPD-Link III, GMSL, GVIF2 as serializer
Input resolution Up to 8190×4095 pixel In the case of 1920×1080 (USB mode) about 80 fps
In the case of 1920×1080 (HDMI mode) about 60 fps
Output bit rate Within 4.0 Gbps In the case of 1920×1080, about 90 fps
In the case of 1280×720, about 180 fps
Supported sync signal Frame Start, Frame End
Number of supported data lanes 1 ~ 4 lanes
Data rate per lane 100 ~ 950 Mbps
Clock rate 50 ~ 475 MHz
Supported pixel formats YUV422 / RGB24 /
Raw8, 10, 12, 16, 20, 24
Other interfaces I2C Frequency:100 kHz Voltage level follows VDDIO
GPIO 16bit, IN/OUT direction control for each bit,
Direct connection to FPGA
Voltage level follows VDDIO
Power supply Board power (input) USB bus power /
Dedicated 2pin connector (5V)
Target side power (output) VDDIO = 1.8 or 2.5 or 3.3 V /
3.3 & 1.2 V output available
VDDIO :IO power supply setting
Other functions Video output timing setting :
Pixel clock unit (including blank),
Multiple frame synchronous output : FrameSYNC signal
Virtual Channel and Embedded Line are available individually
CntinuousClock / NonContinuousClock
are supported
Interface connector 60 pin (QSH-030-01-L-D-A)
FPGA Artix-7 (XC7A35T)
+ Meticom (MC20902)
Meticom is an IC for MIPI D-PHY
Frame memory 256 MByte (DDR3-SDRAM)
USB3.0 chip Cypress EZ-USB FX3
HDMI chip ADV7612
Dimensions length x width x height =
101.6 x 101.6 x 25.7 (mm)
Including spacer (10mm) in height
Attached software
Windows
Video output software SVOGenerator
I2C control software SVMCtl Including SV board update application
Supported SerDes boards
of our company
DS90UB953, CXD4963 etc.,

 

【SV series common specifications】
Application software:NVCap & SVMCtl, Test pattern output function, Image clipping function

Get Adobe' Reader'

To view the pdf files, the Adobe Reader from Adobe Systems is required.